A Power BI report page tooltip uses the hovered data point’s context, but filters on the tooltip page can change what its visuals show. Use this five-step check to identify what carries over and explain differences between a source visual and its tooltip. It is intended for report authors working in Power BI Desktop or the Power BI service editing view.
Prerequisites
- Access: An editable Power BI report and permission to inspect its visuals, filters, and tooltip page.
- Tools: Power BI Desktop or the Power BI service in Editing view; a sample point to hover over.
- Estimated time: About 10–20 minutes, depending on report complexity.
- Difficulty: Intermediate.
Step 1: Identify the tooltip page used by the source visual
Select the visual you want to investigate. In its Format visual pane, expand Tooltips and check the Page setting. If it names a page, that is the manually assigned tooltip. If it is set to Auto, Power BI selects a tooltip based on the fields associated with tooltip pages. Record the page name and the fields used in the source visual, including its category, values, and legend.
In the Filters pane, note filters under Filters on this visual, Filters on this page, and Filters on all pages. A field used in a visual is also part of that visual’s filtering context. A slicer selection or cross-filter interaction may further affect what you see when hovering. Microsoft describes visual, page, and report filters as separate filter levels; the Filters pane helps you inspect them.
Step 2: Inspect filters defined on the tooltip page
Open the tooltip page in the report editor. Inspect the Filters pane for visual-level and page-level filters, then check any slicers on the page. Also confirm that the page is configured as a tooltip in its Page Information settings. Page filters or slicers on the tooltip page can narrow or otherwise alter the result displayed by its visuals, so treat them as a separate layer when tracing the final context.
Do not expect a tooltip page to act like an interactive report page: users cannot select its slicers or scroll within the tooltip. For a controlled preview, a tooltip-page filter can be useful during authoring, but remove temporary preview filters before publishing if they are not part of the intended result.
Step 3: Check whether the hovered fields can filter the tooltip
Hover over a specific data point, not just an empty area of the visual. The point’s category or other compatible fields provide context to the report tooltip. For the tooltip to appear for a field automatically, the source visual must include the relevant field, and the tooltip page must be associated with it. Microsoft notes that tooltip-page filters must be compatible with the source visual’s design; for example, a visual grouped by product is compatible with a tooltip page filtered by product.
Pay particular attention to line charts. The legend field does not act as a filter for the report tooltip, so hovering over one line may still show a tooltip aggregated across the lines for that point. If you need a different tooltip for a particular visual, set its Tooltip Page explicitly instead of relying on automatic selection.
Step 4: Compare one point against a controlled baseline
Choose a point with a simple, recognizable value, such as one product in one month. Hover over it and write down the context you expect: product, month, and any applicable report or page selections. Then temporarily clear or change one filter at a time and hover over the same point again. If the tooltip result changes when you change a slicer, page filter, or source visual interaction, you have identified a contributing filter.
For example, suppose a chart shows sales by month and its tooltip page contains a card for sales. Hover over March while the report is filtered to the West region. The tooltip should reflect the hovered month and compatible report context, subject to filters defined on the tooltip page. If the source visual is cross-highlighted, the tooltip shows the cross-highlighted data. Compare against the same point with the highlight cleared before concluding that a tooltip filter is responsible.
Step 5: Verify the result and document the filter path
Repeat the hover check with another point and, if possible, with another relevant selection. Record the source visual’s tooltip assignment, active report and page filters, hovered category, and tooltip-page filters. This short audit makes it easier for another report author to reproduce the result and distinguishes inherited context from deliberate tooltip-page filtering.
If you are checking a line chart, account for the legend limitation. If you are checking cross-highlighting, clear the selection and compare again. These behaviors are documented for report page tooltips and may explain a result that looks broader or narrower than the hovered mark alone suggests.
Troubleshooting
- The tooltip is blank or does not appear: Confirm the page is marked as a tooltip and that the source visual includes an associated tooltip field, or select the page explicitly in the visual’s Tooltips setting. Make sure the tooltip page contains visuals that use compatible fields.
- The tooltip shows more categories than the hovered mark: For a line chart, check whether you expected the legend to filter the tooltip. Microsoft documents that the legend field does not act as a tooltip filter. Test another visual type or redesign the tooltip to make the intended aggregation clear.
- The tooltip number changes unexpectedly: Inspect filters on all pages, the source page, the source visual, and the tooltip page. Clear cross-highlighting and adjust one filter at a time to isolate the cause. Check the tooltip page’s own filters before assuming the hovered point is the only context.
FAQ
Does a report page tooltip inherit slicer selections?
Its displayed result follows the applicable report context, including compatible filters and interactions. Check the source visual’s active context and the tooltip page’s own filters to confirm the exact outcome.
Can I see every filter affecting a tooltip in one place?
There is not a single tooltip-specific list that explains every part of its context. Inspect the Filters pane at the report, page, and visual levels, then check the tooltip page and test a hovered point.
Can readers change filters inside a page tooltip?
No. Report page tooltips are not interactive: users cannot select slicers or scroll within them. Use a drillthrough page when readers need to interact with filtered details.